Roof Flashing Repair Sugar Land, TX — Sealed Right

When rain only gets in during wind-driven storms, it’s almost always flashing. We fix step, counter and valley flashing across First Colony · Sweetwater · Riverstone · Telfair · Greatwood and ZIPs 77478–77498.

4.9★ — 100+ Reviews
Same-Day Response
Photo-Documented Every Job
7 Days a Week
Reviewed by the Roof Leak Guard field team · Last updated: October 30, 2026
$400–$1,200
Typical flashing repair
94 mph
Beryl gusts that lifted Fort Bend flashing
50+ in
Annual rain testing every seam
7 days
Same-day response, every day of the week
Roof flashing repair in Sugar Land typically costs $300 to $1,200 and takes 2 to 4 hours for one wall or dormer. If the roof only leaks in wind-driven rain, flashing is the likely cause. A proper repair resets or replaces the metal behind the siding. Caulk or tar over the joint lasts a summer or two.

Written by the Roof Leak Guard team · Last updated November 14, 2026

Gulf Rain Hits Flashing From the Side, Not the Top

Flashing is the bent metal at every joint shingles can’t seal: sidewalls, dormers, chimneys, valleys. A vent boot leaks in almost any rain. Flashing is pickier. It stays dry in a straight-down shower and pours when a Gulf squall drives rain sideways out of the southeast.

That’s why homeowners tell us the leak comes and goes. Two-story homes in First Colony and Sweetwater carry long wall-to-roof runs, and every foot of that metal is a place for the wind to push water under a short lap. That on-again, off-again pattern is the signature of a roof flashing leak in Sugar Land.

Beryl’s ~94 mph gusts on July 8, 2024 lifted a lot of it across Fort Bend County. Plenty of those laps never fully leaked until the next hard rain, a year or more later. Roof flashing repair in Sugar Land is where that damage finally gets fixed.

2–4 hrstypical sidewall repair
$400–$1,200most flashing jobs
1 yrtypical repair warranty, terms on estimate
Call Now — Speak to a Local Roofer
Step flashing replaced along a sidewall on a Sugar Land two-story roof
Sidewall step flashing, replaced piece by piece.

Five Kinds of Flashing, Five Ways to Leak

Each joint on your roof uses a different piece of metal, and each fails differently.

Sidewalls

Step flashing

Small L-shaped pieces laced between shingle courses along a sidewall. Leaks when a piece is short, rusted or nailed through the face.

Brick and siding

Counter-flashing

The cap metal set into brick mortar or behind siding. Mortar erodes, the metal pulls loose and water runs behind it.

Chimney flashing repair
Where slopes meet

Valley metal

Carries the heaviest water load on the roof. Worn shingle edges or a cracked seam let it under the underlayment.

Wall base

Kickout flashing

The small bend at the bottom of a sidewall that sends water into the gutter. Missing on many 1990s homes. Water soaks the siding and rots the wall.

Roof edges

Drip edge and apron

Metal along eaves and rakes. Wind lifts it first, and water wicks back onto the fascia and decking.

Roof Flashing Leak in Sugar Land: Reseal, Reset or Replace

Most contractors reach for a caulk gun. Here is how we decide.

Metal we reseal or reset

  • Counter-flashing pulled out of a mortar joint but still straight
  • Sound step flashing with failed sealant at the top lap
  • Drip edge lifted by wind with no rust
  • Valley metal with a loose fastener and no cracks

Metal we replace

  • Rusted or pin-holed step flashing
  • Pieces too short to overlap the shingle course above
  • Flashing nailed through its face
  • Tar-covered joints from earlier repairs

A Sidewall Leak, Before and After

Same wall, same homeowner, same stain upstairs. The difference is the metal behind the siding. Proper Sugar Land roof flashing repair goes behind the siding.

Failed wall flashing before repair on a Sugar Land homeBEFORE
New step flashing installed along the sidewallAFTER

Sidewall step flashing

Old sealant and short pieces pulled out. New metal laced course by course, with the kickout added at the gutter. That’s roof flashing repair in Sugar Land done the slow way.

Storm damage repair

Flashing Repair Prices in Sugar Land

Price by joint, so you see what each section costs.

JointWhat we doTypical cost
Kickout flashingAdd or replace one$150–$350
Sidewall run (15–25 ft)Replace step flashing$600–$1,200
Dormer jointsReplace step and head flashing$500–$1,000
Valley rebuildMetal plus ice-and-water membrane$900–$1,500
Rotted decking foundPer sheet, if needed$400–$800

Estimates for typical homes. Written price before work starts. Full price ranges are in the 2026 roof leak repair cost guide.

What Beryl Left Behind on Sugar Land Flashing

In the weeks after Beryl we kept finding the same thing: sidewall flashing lifted an inch at the top lap, with no stain yet inside. The attic was dry. The next heavy rain wasn’t.

If your roof took that storm and no one has looked at the metal since, a 45-minute check is cheap. Look for rust streaks below the wall, bent drip edge and tar smeared on joints. Ask any roofer doing flashing repair in Sugar Land, TX to photograph the metal first.

Neighborhoods with big two-story rooflines, including First Colony, Sweetwater and Riverstone, show it most. A roof flashing leak in those neighborhoods usually traces back to a wall-to-roof joint. New Territory two-stories have the same long sidewall runs.

Tar over a joint isn’t a repair. It cracks within a couple of Texas summers and hides the real gap.

Roof Flashing Questions — Answered Straight

Straight answers from the local contractors who work Fort Bend County roofs every week.

🔧 The Repair
What’s the difference between step and counter-flashing?

Step flashing is the L-shaped pieces woven into each shingle course along a wall. Counter-flashing covers the top of the step flashing and tucks into the brick or siding so water can’t get behind it.

How long does flashing repair take?

A single wall or dormer usually takes 2–4 hours. A full valley rebuild can take most of a day.

Is roofing tar a permanent fix for flashing?

No. Tar dries, shrinks and cracks in Sugar Land heat, usually within one or two summers.

💰 Cost & Insurance
Will insurance pay for flashing repair?

If a storm lifted or tore it, often yes. Rust, old sealant and poor original installation count as wear and tear.

What raises the price of a flashing job?

Brick work, second-story walls, siding that has to come off and rotted decking under the joint.

Is the repair covered by a warranty?

Yes. Completed repairs come with a written workmanship warranty from the contractor who does the work — typically 1 year on repairs. The exact terms are listed on your estimate before you approve anything.

🏠 Sugar Land Specifics
Why does flashing fail so often in Sugar Land?

Daily heat cycling cracks sealant, and Gulf storms push rain sideways under short laps. Many 1980s–90s homes also still have original galvanized flashing that’s rusting.

Do HOAs care about flashing repairs?

Not usually for like-for-like work. If siding or trim color changes, First Colony, Sweetwater and Telfair HOAs may want to see it first.

Leak Only Shows Up in Windy Storms?
Let’s Check the Flashing.

Same-day flashing inspection anywhere in Sugar Land. Photos of every joint and a written price.

(844) 943-1121

Independent Local Contractors • Fort Bend County • ZIP 77478 · 77479 · 77498

● Sugar Land’s Roof Leak Specialists
The Longer You Wait,
The Worse the Damage Gets.

Every day a roof leak goes unfixed, water spreads into decking, insulation, and drywall.

🔥
Mold starts in 24–48 hours

Once moisture hits your attic insulation or drywall, mold sets fast. Remediation runs $2K–$6K on top of the repair.

🌧
One storm turns a drip into a flood

A vent boot crack or lifted flashing is fine — until the next Sugar Land downpour hits.

💰
Repair now: $350–$800. Wait: $4K+

Catching it early costs a fraction. Most Sugar Land leaks we fix could have been stopped for under $500.


📞 Call Now — Stop the Leak Today
✓ No contracts✓ Same-day response✓ Written estimate first